t-Butylphenyl diphenyl phosphate

  • tert-Butylphenyl diphenyl phosphate
  • Phosphoric acid, (1,1-dimethylethyl)phenyl diphenyl ester
Formula
C22H23O4P
Structure
Description
Clear colorless liquid.
Uses
Flame retardant plasticizer for polyvinyl chloride, flame retardant plasticizer for other vinyl polymers, flame retardant plasticizer for cellulosics.

Registry Numbers and Inventories.
CAS
56803-37-3
EC (EINECS/ELINCS)
260-391-0
Beilstein/Gmelin
NA
Canada DSL/NDSL
DSL
US TSCA
Listed
Austrailia AICS
Listed
New Zealand
Listed
Korea ECL
Listed

Properties.
Formula
C22H23O4P
Formula mass
382.40
Boiling point, °C
245
Vapor pressure, mmHg
1E-6
Density
1.16 g/cm3 (20 C)
Partition coefficient, pKow
5.12 @ 25 C

Hazards and Protection.
Storage
Keep in a cool, dry, dark location in a tightly sealed container or cylinder. Keep away from incompatible materials, ignition sources and untrained individuals. Secure and label area. Protect containers/cylinders from physical damage.
Handling
All chemicals should be considered hazardous. Avoid direct physical contact. Use appropriate, approved safety equipment. Untrained individuals should not handle this chemical or its container. Handling should occur in a chemical fume hood.
Protection
If Tyvek-type disposable protective clothing is not worn during handling of this chemical, wear disposable Tyvek-type sleeves taped to your gloves.
Respirators
Wear a NIOSH-approved half face respirator equipped with an organic vapor/acid gas cartridge (specific for organic vapors, HCl, acid gas and SO2) with a dust/mist filter.
Small spills/leaks
If you spill this chemical, FIRST REMOVE ALL SOURCES OF IGNITION. Then, use absorbent paper to pick up all liquid spill material. Your contaminated clothing and absorbent paper should be sealed in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.
Stability
No data.
Incompatibilities
Can react with oxidizing materials.

Fire.
Flash Point,°C
223.9
Fire fighting
Fires involving this compound should be controlled with a dry chemical, carbon dioxide or halon extinguisher.
Fire potential
This chemical is combustible.

Health.
Exposure effects
The toxicological properties of this material have not been investigated.

First aid
 
   Ingestion
DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, administer a slurry of activated charcoal in water and simultaneously call a hospital or poison control center. IMMEDIATELY transport the victim to a hospital.
   Inhalation
IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. IMMEDIATELY call a physician and be prepared to transport the victim to a hospital even if no symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used.
   Skin
IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. IMMEDIATELY call a hospital or poison control center even if no symptoms (such as redness or irritation) develop. IMMEDIATELY transport the victim to a hospital for treatment after washing the affected areas.
   Eyes
First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.

Transport.